Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
by Piperman » Tue 22.09.2015, 19:34
This question may have asked before , why does nt the petrol filler have a drain ? or is mine blocked? Derek
-
Piperman
- Sadly departed but never forgotten
-
- Posts: 185
- Joined: Sat 30.03.2013, 10:06
- Location: Hants
by alan e » Tue 22.09.2015, 19:46
It has a drain like most yours is blocked
[color=#FFBFFF]Black 1992 M100
2010 black evora
Austin 7 1932 box saloon
MG ZS EV
-
alan e
- God
-
- Posts: 1130
- Joined: Sun 19.02.2012, 20:43
- Location: worthing west sussex
by Brit-Car-Nut » Tue 22.09.2015, 20:34
You do not have the required permissions to view the files attached to this post.
Please contact me via eMail, not by PM
-
Brit-Car-Nut
- God
-
- Posts: 4820
- Joined: Tue 03.07.2007, 17:07
- Location: Charlotte, NC USA
by Piperman » Wed 23.09.2015, 04:39
its never drained i bailed it out in the wet! thanks Derek

-
Piperman
- Sadly departed but never forgotten
-
- Posts: 185
- Joined: Sat 30.03.2013, 10:06
- Location: Hants
by rip » Wed 23.09.2015, 09:26
You should find the bottom end of this if you look under the car. Mine blocked at the elbow near the top, just below the drain hole.
You can try some compressed air from above but this did not work for me.
1990 SE
-

rip
- God
-
- Posts: 5904
- Joined: Sun 08.04.2007, 07:48
- Location: Milton Keynes, UK
by Jon » Sun 27.09.2015, 08:52
Just a word of warning - the drainage tube seems to perish, become brittle and crack....mine fell into several pieces upon touching it a few days ago....
P.s. Does anywhere know where the tube runs to after it goes through the bulk head round the fuel tank??
-

Jon
- Fanatic
-
- Posts: 250
- Joined: Mon 12.05.2003, 08:54
by rip » Sun 27.09.2015, 20:34
Jon wrote:P.s. Does anywhere know where the tube runs to after it goes through the bulk head round the fuel tank??
Almost (but not quite) straight down. There is a pathway for it , honest.
1990 SE
-

rip
- God
-
- Posts: 5904
- Joined: Sun 08.04.2007, 07:48
- Location: Milton Keynes, UK
by donsladek » Fri 07.06.2019, 23:17
I've had some success with a thin strip of Scotchbrite pad, shaped into a "U", then pushing the legs into the inlet of the drain to act as a filter. It still stops draining over time, but when stopped up, I poke it a bit and it drains, and prevents larger debris from entering the drain system.
Don Sladek
Calypso Red '91 #37594
If everything seems under control, you're just not going fast enough - Mario Andretti
-

donsladek
- Fanatic
-
- Posts: 547
- Joined: Sun 07.08.2005, 22:19
- Location: New Berlin, Wisconsin USA
by dapinky » Sat 08.06.2019, 10:08
Don,
Another top tip from LEC - I never thought about making a filter .... just spend too much time clearing the pipe and clearing all the 'sludge' from the surrounding well whenever I notice it getting bad.
must go.... I've got to find the scotchbrite

Dave
Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it
...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
-

dapinky
- LEC Administrator
-
- Posts: 10605
- Joined: Sun 15.10.2006, 12:54
- Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).
Return to Hood/Top, Bodywork and Fittings
Who is online
Users browsing this forum: No registered users and 3 guests