Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
by Elanthrapist » Tue 15.06.2021, 19:03
Hello all,
I am just about to have the sill areas sprayed due to stone chips. I have aquired a set of 4 anti chip film protectors. Does anyone have these fitted and if so can you supply pictures of them front and back. The difficulty I have is what goes where, it's not obvious and I want it to look right and also protect the right areas.
With many thanks, best regards, George.
1968 Elan S4 dhc (Now sold).
1973 Elan Plus 2 S130/5 [Lagoon Blue].
1994 Elan M100 S2[Medina Green].
-
Elanthrapist
- Newbie
-
- Posts: 18
- Joined: Sat 03.12.2016, 19:42
- Location: Chateaubriant, France.
by scotlan » Tue 15.06.2021, 21:28

Mine has 4 chip protectors, the large one above the sill line and the narrow one directly below. None at the front
hope this helps
-

scotlan
- Enthusiast
-
- Posts: 139
- Joined: Sat 01.01.2011, 10:51
- Location: Perth, Scotland
by johnj » Wed 16.06.2021, 10:46
My car had film strips on it when I bought it but dirt had got behind them making them look nasty. I got them off ok but trying to put them on was a nightmare. I wasted one and gave up. Is there a technique to put them on smoothly?
-
johnj
- Enthusiast
-
- Posts: 178
- Joined: Mon 04.01.2010, 23:56
- Location: Cumbria
by david924s » Wed 16.06.2021, 11:49
I don't have them on the Elan, but when I replaced the ones on my 944 I sprayed the area on the car where they were to go with soapy water (couple of drops in a spray bottle) then when you fit the film it can move about on the water until you get it right then use a squeegee to push out the water underneath. Bit like putting transfers onto models when you were a kid!
-
david924s
- Enthusiast
-
- Posts: 145
- Joined: Mon 17.09.2018, 07:48
- Location: Ingleby Barwick, Stockton on Tees
by johnj » Wed 16.06.2021, 21:06
A long time since I was a kid

but will give your technique a try. Thank you
-
johnj
- Enthusiast
-
- Posts: 178
- Joined: Mon 04.01.2010, 23:56
- Location: Cumbria
by exeterjeep » Sat 30.04.2022, 20:37
I have recently done all 4 on my S2, took a while to get off using the heat gun on low and some sticky stuff remover, the slightly soapy way was fine.
Has anyone fitted a similar PPF layer to protect the area where the soft top sits on the rear deck. Managed to get off most of the marks and a good polish helped.
-
exeterjeep
- Enthusiast
-
- Posts: 120
- Joined: Sun 14.11.2021, 13:04
- Location: Exeter, Devon
by Rambo » Sun 01.05.2022, 20:44
I believe Geof (only one effin') Smith did a group buy a few years ago. He may have one or two left?
PS I could do with a couple too Geof. In lieu of a couple of Beadnell's finest

-

Rambo
- Don't push me
-
- Posts: 9144
- Joined: Wed 24.12.2003, 00:37
- Location: Both sides of the Tweed
by dapinky » Mon 02.05.2022, 10:24
Rambo wrote:PS I could do with a couple too Geof. In lieu of a couple of Beadnell's finest

I know of a tall ginger bloke with a respray who would like some as well.......
Dave
Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it
...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
-

dapinky
- LEC Administrator
-
- Posts: 10605
- Joined: Sun 15.10.2006, 12:54
- Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).
Return to Hood/Top, Bodywork and Fittings
Who is online
Users browsing this forum: No registered users and 8 guests