Moderators: theelanman, dapinky, clemo, Nige, Specky, Sy V, GeoffSmith, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman
by basher » Thu 26.10.2017, 21:00
Anyone know where I can get hold of these identical to what came off?
I ripped one of mine in the Loch Ness Speed Bump incident and I'd like to replace them all. I have tried Halfrauds and EBay thinking it would be easy to find them but that's not the case.
A circular lump of rubber 3.5cm thick, 5cm diameter with 2 circular d shaped holes.
Any ideas?
-

basher
- Enthusiast
-
- Posts: 200
- Joined: Tue 02.11.2010, 18:19
- Location: Essex
by Saltire » Thu 26.10.2017, 21:39
Jonathan
1995 Elan S2 no 512, BRG/magnolia, last of 4 UK S2 to this spec
2010 Fiat Panda 100HP, bossanova white/grey (the rollerskate)
2017 BMW F48 X1 2.0D AWD, Mediterranean blue/magnolia (the workhorse)
-

Saltire
- God
-
- Posts: 1110
- Joined: Sun 05.04.2015, 22:27
- Location: Left foot in Wiltshire, right foot in Gloucestershire
-
by Rusty Wishbone » Thu 26.10.2017, 21:58
The ones sold by SJs are an absolute nightmare to get on and off. I got a couple of hangers with bigger holes from my local garage.
You might try your local tyre & exhaust garage. They will probably have lots of different shapes and sizes.
-
Rusty Wishbone
- Fanatic
-
- Posts: 645
- Joined: Fri 28.12.2012, 13:16
- Location: Tunbridge Wells, Kent
by basher » Fri 27.10.2017, 19:17
Thick of me. I should have tried SJ first, thought they would be common.
Understand that they are hard to put on, taking them off was no Hawaiian Beach Barbeque either!!
Might try local garage too!
-

basher
- Enthusiast
-
- Posts: 200
- Joined: Tue 02.11.2010, 18:19
- Location: Essex
by Danevansgolf » Fri 27.10.2017, 23:41
I have 2 old, but in perfect condition exhaust hangers. You can have them if you want. I replaced my exhaust a few months back and replaced all the hangers, just cos.
You do not have the required permissions to view the files attached to this post.
-
Danevansgolf
- Enthusiast
-
- Posts: 112
- Joined: Mon 13.05.2013, 23:38
- Location: Cardigan, Ceredigion
by Danevansgolf » Fri 27.10.2017, 23:43
Forgot to say. Pm me your address and I’ll sent you them beginning of next week. Only cost a couple of quid so call it on me.
-
Danevansgolf
- Enthusiast
-
- Posts: 112
- Joined: Mon 13.05.2013, 23:38
- Location: Cardigan, Ceredigion
by basher » Sat 28.10.2017, 14:41
That's very decent of you, thanks.
-

basher
- Enthusiast
-
- Posts: 200
- Joined: Tue 02.11.2010, 18:19
- Location: Essex
by Danevansgolf » Sun 29.10.2017, 10:40
Just about to package these up for you. And have realised that on them they say FORD. So obviously if any one needs spares you’d probably be able to get the from a ford dealer
And probably cheaper. Enjoy and enjoy if Luck fitting these little bas***ds back to the car.
You do not have the required permissions to view the files attached to this post.
-
Danevansgolf
- Enthusiast
-
- Posts: 112
- Joined: Mon 13.05.2013, 23:38
- Location: Cardigan, Ceredigion
by GeoffSmith » Mon 01.10.2018, 15:32
Mine appeared to be standard GM parts however @Lotus70 Pinky reckoned that the Ford one he used to have was better but I'm wondering if anyone has tried something like
this or
this?
Calypso Red S2 #417
USB ElanScan interfaces - £55 incl. P&P.
-

GeoffSmith
- Kitty Fiddler
-
- Posts: 14280
- Joined: Fri 03.02.2006, 21:57
- Location: S2#417 in Tytherington, Gloucestershire
-
by Simon_P » Mon 01.10.2018, 16:42
Exhaust mounts should be rubber to avoid noise transmission issues.
Having snatched the exhaust mount out of Pinky's hand @Lotus70 I can say that it is on the large side - I'm not complaining though as it was all that was holding my exhaust on on the journey home - Thanks Dave!
I will be at a mainstream car parts supplier sometime this week so will look through whatever they have and post here.
-
Simon_P
- God
-
- Posts: 1116
- Joined: Fri 06.08.2004, 12:33
- Location: Kent UK
by Brit-Car-Nut » Mon 01.10.2018, 17:15
Part Number A100S6014F is only £6.43 at SJs. I am amazed that Lotus would discontinue such a common part.
-
Brit-Car-Nut
- God
-
- Posts: 4220
- Joined: Tue 03.07.2007, 17:07
- Location: Charlotte, NC USA
-
by Simon_P » Mon 08.10.2018, 09:09
Looking at the original hangers there is a GM part number.
9281771
This is also a Land Rover part number. There also seems to be a direct cross reference to a Volvo part.
a search for "9281771 Exhaust" brings up plenty of choice.
The ones I took off were round the GM ones I'm putting back on are square - critical dimensions are the same.
-
Simon_P
- God
-
- Posts: 1116
- Joined: Fri 06.08.2004, 12:33
- Location: Kent UK
Return to Exhaust
Who is online
Users browsing this forum: No registered users and 1 guest