Door holders

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Door holders

Postby holty » Fri 03.03.2006, 21:29

Is it easy to take the leather door bags off or will i have to take the whole door card off. The old one's are a bit tatty and i want them replacing cheers holty!
User avatar
holty
Enthusiast
 
Posts: 143
Joined: Sat 15.11.2003, 00:21

Postby pjohn151 » Fri 03.03.2006, 22:20

The bad news is that you will have to get the door panel off or at least unscrew them, to get to where the elastic top of the pockets are secured. The easy bit is undoing the bottom of the pockets - unscrew the screws that hold down a plastic clamping strip around the inside of the pocket at the bottom. If you are re colouring them, then just undoing the bottom might be sufficient, indeed if you need to at all.

Phil
Last edited by pjohn151 on Fri 03.03.2006, 23:19, edited 1 time in total.
SOLD - '90G BRG Elan SE, 42k miles
Excellent condition - see for sale section

Now Elanless
User avatar
pjohn151
Fanatic
 
Posts: 257
Joined: Tue 20.05.2003, 09:19
Location: Milton Keynes, Bucks, UK

Postby Paul.P » Fri 03.03.2006, 23:12

I know on mine, the screws that go through the plastic pieces have a small metal piece on the inside of the doorcard, so when you unscrew them the metal strips fall down inside the doorcard, requiring the removal of the doorcard to put them back. Hope that makes sense ?
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby pjohn151 » Fri 03.03.2006, 23:22

Didn't know about that bit - after all I have never had to get them off.

Access to behind the doorcard is pretty much a necessity then.

Phil

Is that 100 posts yet?
SOLD - '90G BRG Elan SE, 42k miles
Excellent condition - see for sale section

Now Elanless
User avatar
pjohn151
Fanatic
 
Posts: 257
Joined: Tue 20.05.2003, 09:19
Location: Milton Keynes, Bucks, UK

Postby Paul.P » Fri 03.03.2006, 23:28

Well it is on mine Phil, i only found out when i took my old ones off couple of weeks ago & heard the jingling as the little tabs all fell to the bottom of the doorcard & one or two actually fell out, & i realised what i had done ! :lol:
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby holty » Sun 05.03.2006, 11:55

Look's like i'll have to take the lot off then. Thank's for advice!
User avatar
holty
Enthusiast
 
Posts: 143
Joined: Sat 15.11.2003, 00:21

Postby TheBard » Sun 05.03.2006, 17:23

Make sure you have your spare orange clips for the locks ready before removing the doorcard. I've got pretty good at the removal and refit, but still have half a dozen orange clips on hand just in case!

And remember the two golden rules, "Patience", and no matter how tempting it may be "Do not pry anything with a screwdriver". :roll:

I'll go back to mucking around with my possible PAS fluid leak now :(

Ian
Ford Fiesta Mk2, VW Polo, Golf GTi, Lotus Elan, Honda Accord Coupe V6.

Calypso Red Cali #7683 - Bought at 29,000 miles, and sold at 75,000miles.
User avatar
TheBard
Fanatic
 
Posts: 652
Joined: Sun 16.01.2005, 05:22
Location: Washington D.C.

Postby pjohn151 » Sun 05.03.2006, 21:21

You may get away without having to replace the red clips, as if you are only doing the pockets, you may have enough access without totally removing the doorcard - I replaced my door speakers without fully removing the doorcard, I just undid everything apart from the clip on the lock button and was able to ease the casing out enough.

Phil
SOLD - '90G BRG Elan SE, 42k miles
Excellent condition - see for sale section

Now Elanless
User avatar
pjohn151
Fanatic
 
Posts: 257
Joined: Tue 20.05.2003, 09:19
Location: Milton Keynes, Bucks, UK

Postby John_W » Sun 05.03.2006, 21:23

holty wrote:Look's like i'll have to take the lot off then. Thank's for advice!

Holty,
I don't know if you are aware that Charlie_X did a good job of documenting what you have to do to get at the door innards. It's on the old site, and the link to Charlie's site doesn't work currently, so have a look here:.

John
User avatar
John_W
Heid-bummer
 
Posts: 3780
Joined: Mon 21.04.2003, 12:31
Location: Aberdeen

Postby Doug » Mon 06.03.2006, 06:10

also know that the Lotus factory trim shop can do new pockets, door cards, seats, etc . . .
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA

Postby holty » Tue 07.03.2006, 18:26

Gonna have a go at the weekend, cause i want this little job out of the way. Everytime i do one job another start's. Now i've got boost creep. But that's another thread altogether. :roll:
User avatar
holty
Enthusiast
 
Posts: 143
Joined: Sat 15.11.2003, 00:21


Return to Interior

Who is online

Users browsing this forum: No registered users and 3 guests