Carbon fibre sparkplug and oil seperator covers

[Elanlover]

I'm guessing from this comment:

Blair, I'm not really a composite fabricator - I just carve bits up!

That you've got flat sheets of CF and are simply cutting shapes? If so, then I can't see anything else that's flat that could be substituted for a CF piece. The timing belt cover would look pretty good in CF as well as a few other little black plastic covers but they are all complicated pieces. Don't know if you can make those (or even want to).

[djcar]

both

[Jeemy]

List for interest in plug cover:-
1)
2)
3)

List for interest in oil seperator cover:-
1) maz_r
2) daveA
3)

List for interest in both:-
1) rip
2) DaveB
3)pjw12
4) texas2201
5) Aoki Magic Pants
6) MattRI
7) G UK
8 ) MPx
9) djar
10) Jeemy

[barefoot]

Please put me down for both

[paulsmithmk]

List for interest in plug cover:-
1)
2)
3)

List for interest in oil seperator cover:-
1) maz_r
2) daveA
3)

List for interest in both:-
1) rip
2) DaveB
3)pjw12
4) texas2201
5) Aoki Magic Pants
6) MattRI
7) G UK
8 ) MPx
9) djar
10) Jeemy
11) Paulsmithmk

[DaveB]

Just to make sure barefoot gets on the list...

List for interest in plug cover:-
1)
2)
3)

List for interest in oil seperator cover:-
1) maz_r
2) daveA
3)

List for interest in both:-
1) rip
2) DaveB
3)pjw12
4) texas2201
5) Aoki Magic Pants
6) MattRI
7) G UK
8 ) MPx
9) djar
10) Jeemy
11) Paulsmithmk
12) barefoot

[enndee]

Ooh, yes please, both for me

List for interest in plug cover:-
1)
2)
3)

List for interest in oil seperator cover:-
1) maz_r
2) daveA
3)

List for interest in both:-
1) rip
2) DaveB
3)pjw12
4) texas2201
5) Aoki Magic Pants
6) MattRI
7) G UK
8 ) MPx
9) djar
10) Jeemy
11) Paulsmithmk
12) barefoot
13) enndee

[davidcgriffiths]

Ooh, yes please, both for me

List for interest in plug cover:-
1)
2)
3)

List for interest in oil seperator cover:-
1) maz_r
2) daveA
3)

List for interest in both:-
1) rip
2) DaveB
3)pjw12
4) texas2201
5) Aoki Magic Pants
6) MattRI
7) G UK
8 ) MPx
9) djar
10) Jeemy
11) Paulsmithmk
12) barefoot
13) enndee

14) DavidcGriffiths

[djcar]

well after seeing what someone else did using hydrographics I found a place near me that does this so shipped off parts and they came back fantastic. I'm happy




I sand blasted the metal covers and primed them myself before I shipped them. cost about $150 including the shipping both ways.
Upgraded wires and spark plugs too!

[djcar]

Before


I hope to get the valve cover powdered coated and other parts cleaned up refinished ect ect soon.

[esprit888]

Dave,
These look great, what's the name of the company?

[djcar]

http://www.miragehydrographics.com/

my goal this winter was too clean up the engine area getting parts re finished. next I'd like to do the turbo shields in chrome.

also some bad news the rear window split on me. not quite sure how I did

So it needs a new window but I hardly ever drive it with the top up. I'm hoping next summer to get that done before next fall.

[djcar]

If you notice the CAS cover is a slightly different pattern than the others has yellow/gold in it.

I also put in the new wires and new sprk plugs

also the cover is missing 2 of the screws know where to get replacements screws?