Porting the wastegate

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Postby ailwyn » Thu 07.02.2008, 20:22

Put me down for 2 lots of everything :D
ailwyn
Forum Member
 
Posts: 3361
Joined: Tue 09.08.2005, 20:45

Postby ailwyn » Fri 08.02.2008, 15:18

As taking turbos off is now flavour of the week, I decided to join in.

Was also considering removing the exhaust manifold to see if it could be cleaned up and made to look more presentable than the current lump of rust. Am I risking knackering studs or nuts that can't be (easily) replaced?

Also, on the rebuild, I was going to try and replace the turbo to downpipe studs/nuts with bolts? Is there any disadvantage to this? Same goes for the turbo to manifold mounting.
ailwyn
Forum Member
 
Posts: 3361
Joined: Tue 09.08.2005, 20:45

Postby Russc » Fri 08.02.2008, 16:20

I`m just finishing putting mine back together after porting.

I also had to replace the manifold as mine was shagged.

As people have said the studs did break off, 2 of mine to be precise. One of them i had to get drilled out and rethreaded but all ok now. Replaced tow of them with the normal studs and then 2 with high tensile bolts (the longer two).

I also used bolts for mounting the turbo to the manifold. Was straight forward enough.

The only thing i would do differently is when i took the power steering pump bracket off. I took the holding bracket on the top off easily enough but also took the bracked that mounts onto the engine totally off. Took me an hour to get it line dup again, i would just loosen them next time. The reason i took them off is becuase it`s near impossible to remove the far left nut to take the manifold off.
User avatar
Russc
Fanatic
 
Posts: 502
Joined: Thu 02.03.2006, 14:51
Location: North/Kent SE/London

Postby ailwyn » Sun 17.02.2008, 22:21

Might seem like a dumb question, but what tool do I need to remove the studs that hold the exhaust manifold to the engine?

Thanks

Ailwyn
ailwyn
Forum Member
 
Posts: 3361
Joined: Tue 09.08.2005, 20:45

Postby Russc » Sun 17.02.2008, 23:04

Sorry, not sure on that one. I left mine in :)
User avatar
Russc
Fanatic
 
Posts: 502
Joined: Thu 02.03.2006, 14:51
Location: North/Kent SE/London

Postby GeoffSmith » Sun 17.02.2008, 23:04

ailwyn wrote:Might seem like a dumb question, but what tool do I need to remove the studs that hold the exhaust manifold to the engine?

Thanks

Ailwyn


I think they're star drive. I had no trouble removing the nuts and I've left the studs well alone as they're not to bad and are going into alloy so there is potential for deep s**t.

Paul used VHT paint (and so have I but I could only get 1050°F so it may not last). What have others done about the turbo? There's a lot of masking to be done to spray it and it gets very hot so the paint may not last.
You do not have the required permissions to view the files attached to this post.
Calypso Red S2 #417

USB ElanScan interfaces - £60 incl. UK P&P & £65 incl. ROW P&P
User avatar
GeoffSmith
Kitty Fiddler
 
Posts: 15628
Joined: Fri 03.02.2006, 21:57
Location: S2#417 in Tytherington, Gloucestershire

Postby Paul.P » Mon 18.02.2008, 08:50

Geoff, if your worried about them manifolds, get them sent here, its the pukka job for them, its the same as Jet Hot Coating in the states, normal lead time is 10 days. I dealt with a bloke called Peter Carter.

www.camcoat.com
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby GeoffSmith » Mon 18.02.2008, 09:09

Paul.P wrote:Geoff, if your worried about them manifolds, get them sent here, its the pukka job for them, its the same as Jet Hot Coating in the states, normal lead time is 10 days. I dealt with a bloke called Peter Carter.

www.camcoat.com


Thanks Paul. Having read your thread, that was the original plan but I'm out of time, so it's back together for Donington and the summer then strip down (easy with the stainless fasteners!) and coat and fit the PCE next Winter. I thought I had found a place in Bristol (they do a lot of work for Airbus/Rolls and racing teams) but they advised me that their product is probably too brittle for this application. I guess I can have a look at your heatshields at Donny as well to see how it looks. :lol:
Calypso Red S2 #417

USB ElanScan interfaces - £60 incl. UK P&P & £65 incl. ROW P&P
User avatar
GeoffSmith
Kitty Fiddler
 
Posts: 15628
Joined: Fri 03.02.2006, 21:57
Location: S2#417 in Tytherington, Gloucestershire

Postby Paul.P » Mon 18.02.2008, 09:29

geoffsmith wrote:Thanks Paul. Having read your thread, that was the original plan but I'm out of time, so it's back together for Donington and the summer then strip down (easy with the stainless fasteners!) and coat and fit the PCE next Winter. I thought I had found a place in Bristol (they do a lot of work for Airbus/Rolls and racing teams) but they advised me that their product is probably too brittle for this application. I guess I can have a look at your heatshields at Donny as well to see how it looks. :lol:


Doubt i'll have them on at Dony Geoff, they won't go on till get the PCE & swap turbo's, but i can bring the bits i had done to show you ?, also Dico had his Stiffy done in the black coating, you maybe able to see it on his car ?
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby GeoffSmith » Mon 18.02.2008, 09:34

Paul.P wrote:Doubt i'll have them on at Dony Geoff, they won't go on till get the PCE & swap turbo's, but i can bring the bits i had done to show you ?, also Dico had his Stiffy done in the black coating, you maybe able to see it on his car ?


It would be good to see them in the flesh if you could bring them Paul - maybe even show them on the stand.

I guess I could nip up to Manc and take a peek in his garage. :twisted:
Calypso Red S2 #417

USB ElanScan interfaces - £60 incl. UK P&P & £65 incl. ROW P&P
User avatar
GeoffSmith
Kitty Fiddler
 
Posts: 15628
Joined: Fri 03.02.2006, 21:57
Location: S2#417 in Tytherington, Gloucestershire

Postby Paul.P » Mon 18.02.2008, 09:44

geoffsmith wrote:It would be good to see them in the flesh if you could bring them Paul - maybe even show them on the stand.

I guess I could nip up to Manc and take a peek in his garage. :twisted:


If there wanted for the stand, its no problem Geoff, just let me know ?

If we're very lucky, i think the beast might be making one of them rare appearances, but don't hold your breath :smt009
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby dapinky » Mon 18.02.2008, 10:01

ailwyn wrote:Might seem like a dumb question, but what tool do I need to remove the studs that hold the exhaust manifold to the engine?

Thanks

Ailwyn


Ailwyn,

It ain't a dumb question at all!

It is a star drive socket, like virtually everything on a modern Vauxhall!

They have a unique sizing/numbering system, a bit like torx fittings, and i can't remember the one i used :(

I can remember that it was quite small and that it only had a 1/4 drive on the socket - so i was a bit concerned about how tight they were going to be - as it was, they came out easily (3 attached to the nuts, the rest on their own).
Dave

Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it


...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
User avatar
dapinky
LEC Administrator
 
Posts: 10626
Joined: Sun 15.10.2006, 12:54
Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).

Postby ailwyn » Mon 18.02.2008, 10:21

Dave,

Thanks for the pointer. I have 7 nuts removed, 8th nut is rusted to the stud, so the stud came out with nut attached, really easy though, and I'm now left with the magic 9th... the one that requires Paul Daniels to remove it from the right hand side (of the car) :)

You don't remember what the correct term is? I'll do a search to see if I can figure it out too.

Thanks

Ailwyn
ailwyn
Forum Member
 
Posts: 3361
Joined: Tue 09.08.2005, 20:45

Postby dapinky » Mon 18.02.2008, 10:54

Ailwyn,

This type of thing is what you need.

I've got the set pictured at #5 on the catalogue page.

Just been out to the car and the size needed appears to be E8.

How much of a rush are you in?

Do you want me to stick the socket in the post - if so, PM me your address and I'll stick it in an envelope.
Dave

Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it


...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
User avatar
dapinky
LEC Administrator
 
Posts: 10626
Joined: Sun 15.10.2006, 12:54
Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).

Postby ailwyn » Mon 18.02.2008, 11:15

Dave,

That confirms what I just found... although via ebay:

http://cgi.ebay.co.uk/10-YES-10-STAR-PI ... dZViewItem

Thanks for the offer, I'll wait for the one's I've ordered to arrive, have plenty of other jobs to be getting on with. :D

Ailwyn
ailwyn
Forum Member
 
Posts: 3361
Joined: Tue 09.08.2005, 20:45

Postby rip » Tue 19.02.2008, 09:39

ailwyn wrote:the one that requires Paul Daniels to remove it from the right hand side (of the car) :)

You don't remember what the correct term is?


You'll like it...but not a lot.

:lol:
1990 SE
User avatar
rip
God
 
Posts: 5905
Joined: Sun 08.04.2007, 07:48
Location: Milton Keynes, UK

Postby rip » Tue 19.02.2008, 09:41

Paul.P wrote:
If we're very lucky, i think the beast might be making one of them rare appearances, but don't hold your breath :smt009


Just how optimistic are you? :-D
1990 SE
User avatar
rip
God
 
Posts: 5905
Joined: Sun 08.04.2007, 07:48
Location: Milton Keynes, UK

Postby GeoffSmith » Sun 24.02.2008, 21:10

She lives! Started off the button and now warming up in the garage with some Radflush in. All I need to do now is disable the alarm to turn the indicators off. :evil:
Calypso Red S2 #417

USB ElanScan interfaces - £60 incl. UK P&P & £65 incl. ROW P&P
User avatar
GeoffSmith
Kitty Fiddler
 
Posts: 15628
Joined: Fri 03.02.2006, 21:57
Location: S2#417 in Tytherington, Gloucestershire

Postby Specky » Sun 24.02.2008, 21:46

geoffsmith wrote:She lives! Started off the button and now warming up in the garage with some Radflush in. All I need to do now is disable the alarm to turn the indicators off. :evil:


Cue Monty... :shock:



TTFN
If you have a problem, if no one else can help, and if you can find them, maybe you can hire... The N/A-Team.
User avatar
Specky
Moderator
 
Posts: 5982
Joined: Sun 07.09.2003, 23:19
Location: Swindon

Postby Monty » Sun 24.02.2008, 21:53

Specky wrote:
geoffsmith wrote:She lives! Started off the button and now warming up in the garage with some Radflush in. All I need to do now is disable the alarm to turn the indicators off. :evil:


Cue Monty... :shock:



TTFN



:smt017
Image
User avatar
Monty
Chunder King!
 
Posts: 7977
Joined: Sun 11.01.2004, 22:32
Location: Leeds

PreviousNext

Return to Turbos, Boost, and Intakes

Who is online

Users browsing this forum: No registered users and 1 guest