How to re-waterproof a hood

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

How to re-waterproof a hood

Postby browfish » Wed 07.12.2005, 15:49

My hood seems to slowly be seeping water through it latley, i bit like old tents do with little beads of water forming on the inside. Is there a way to re-waterproof it. I was thinking of going t a camping shop and seeing if there was a spray of somekind that would do this. Anyone else done something similar?
browfish
Tinkerer
 
Posts: 50
Joined: Wed 13.07.2005, 15:50

Postby theelanman » Wed 07.12.2005, 16:03

User avatar
theelanman
Moderator
 
Posts: 7296
Joined: Fri 30.04.2004, 15:52
Location: peak district

Postby Nige » Wed 07.12.2005, 16:37

Agree entirly with the use of Renovo. But also this time of year it's quite possible that it isn't leakage but condensation. This can be reduced by using dessicant packs inside the car.
Back in Blighty
User avatar
Nige
LEC Administrator
 
Posts: 3030
Joined: Thu 10.07.2003, 19:04
Location: Dorset and Surrey

Postby paza1 » Wed 07.12.2005, 21:32

Fabrisil is another option, possibly cheaper than Renovo. I used Fabrisil after applying the Renovo Soft top Reviver. This combination has given a decent result.
Silver 1992 SE Turbo.
paza1
Fanatic
 
Posts: 687
Joined: Thu 09.06.2005, 22:46
Location: Chester

Postby Paul.P » Wed 07.12.2005, 22:01

Was told by very reputable lotus dealer that there was no chance of water actually getting through the roof material, only the seals, unless there's a rip somewhere. I would be more inclined for it to be condensation, noticed this week, if i leave my van all day with windows shut, front screen covered in condensation !
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby John_W » Wed 07.12.2005, 23:06

User avatar
John_W
Heid-bummer
 
Posts: 3780
Joined: Mon 21.04.2003, 12:31
Location: Aberdeen

Postby Ashaman » Thu 08.12.2005, 03:22

The Rennovo stuff is good, however it might be a short-term fix if the top is deteriorating.

There are several layers to the top, the cotton underside, a rubber middle, and then the canvas-like outer shell. Apparently over time the rubber center layer breaks down. When this happens, the top can LOOK great, but will not be water tight due to cracking & dry-rot within the center.

If the problem IS damage to the middle section, there really isn't a long term fix other than repairing the top. Unfortunately, I will probably be in this boat within the next couple years, mine is getting pretty worn...ugh.
Stompin' out one MOTHER of a carbon footprint.

http://www.cardomain.com/ride/608786
User avatar
Ashaman
Fanatic
 
Posts: 671
Joined: Mon 21.04.2003, 20:22
Location: Crown Point, IN


Return to Hood/Top, Bodywork and Fittings

Who is online

Users browsing this forum: No registered users and 8 guests