Boot/Trunk lock getting stuck

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Boot/Trunk lock getting stuck

Postby Fubar1764 » Sun 07.05.2006, 07:23

Anyone have any problems with their boot key getting stuck? Here's the scenario:
I put the key to open up the boot (trunk for us Yanks). Turn the key, the boot opens like normal. Then, I have trouble twisting the key back to remove the key and close the boot.
Anyone experience such problems? Maybe I should get some warranty work! :lol:
"Lawyer, gambler, bookie, loan-shark, light arson, sundry interests in areas of questionable legality"

-Your "Jack" of all trades
User avatar
Fubar1764
God
 
Posts: 1493
Joined: Fri 14.11.2003, 03:56

Postby Candles » Sun 07.05.2006, 07:57

I had it sticking when trying to unlock. It seemed easier if I turned it the opposite way first then tried unlocking. In the end, something happened to it and I ended up dismantling the whole thing, cleaning & re-lubing then re-assembling it all tightly in place. Works fine now.

Candles.
User avatar
Candles
God
 
Posts: 1496
Joined: Tue 22.04.2003, 09:58
Location: Bristol, UK

Postby Fubar1764 » Sun 07.05.2006, 08:01

Well then, sounds like I've a project for the morning! ;) Thanks!
"Lawyer, gambler, bookie, loan-shark, light arson, sundry interests in areas of questionable legality"

-Your "Jack" of all trades
User avatar
Fubar1764
God
 
Posts: 1493
Joined: Fri 14.11.2003, 03:56

Postby Doug » Sun 07.05.2006, 08:34

yeah, and take some pictures of your stealth car too while at it :x
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA

Postby Candles » Sun 07.05.2006, 08:35

The thing that makes it tricky is the access (as always with the Elan!). You have to work through the rubber grommet on the bottom with various pin-nosed pliers and chop sticks!
User avatar
Candles
God
 
Posts: 1496
Joined: Tue 22.04.2003, 09:58
Location: Bristol, UK

Postby Fubar1764 » Sun 07.05.2006, 09:11

Chop sticks I can handle. Needle nose pliers? What am I, a dwarf?! :evil:
"Lawyer, gambler, bookie, loan-shark, light arson, sundry interests in areas of questionable legality"

-Your "Jack" of all trades
User avatar
Fubar1764
God
 
Posts: 1493
Joined: Fri 14.11.2003, 03:56

Postby Fubar1764 » Sun 07.05.2006, 19:20

Well, lubed the locking mechanism again. Last time, I used motor oil. This time, lithium grease. This might turn into an annual inconvenience. We shall see. . .
"Lawyer, gambler, bookie, loan-shark, light arson, sundry interests in areas of questionable legality"

-Your "Jack" of all trades
User avatar
Fubar1764
God
 
Posts: 1493
Joined: Fri 14.11.2003, 03:56

Postby nitroman » Tue 09.05.2006, 05:59

Doug, here's a picture of Jack's stealth car I took at Amelia. It also proves that body shops' can do a phenomenal job making an Elan like new. Not like a new Elan; just like new.

BTW, one of the cool things about Amelia is that you are free to dress "in period" with your car if you wish. About 20% of people do. It lets you know there were some pretty hot looking babes in "grandma's day." Of course, it doesn't hurt that Florida has the most beautiful women in the world. To a large extent this is because there is no "off season", no months of fattening up behind thick-clothes... you are always on the field.
Last edited by nitroman on Tue 09.05.2006, 18:06, edited 1 time in total.
User avatar
nitroman
Moderator
 
Posts: 3554
Joined: Fri 18.04.2003, 01:17
Location: Jacksonville, FL

Postby Paul.P » Tue 09.05.2006, 07:02

nitroman wrote: Of course, it doesn't hurt that Florida has the most beautiful women in the world.


But are they as obedient as the Asian women ?
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
Paul.P
God
 
Posts: 4970
Joined: Sun 14.12.2003, 18:18
Location: Oakham, Rutland

Postby nitroman » Tue 09.05.2006, 09:26

It all depends what you want in a person.
User avatar
nitroman
Moderator
 
Posts: 3554
Joined: Fri 18.04.2003, 01:17
Location: Jacksonville, FL

Postby TommyK » Thu 11.05.2006, 06:00

I don't know about that... I've been all over the world and I lived in Orlando, FL for over a year and I have found Sardegna to have a higher concentration of beautiful women. But as they say, "Beauty is in the eye of the beholder." What was this thread about again?
TommyK
Enthusiast
 
Posts: 167
Joined: Fri 01.10.2004, 22:38
Location: Benicia, CA

Postby nitroman » Thu 11.05.2006, 07:26

Is Orlando on the coast? Nope.
User avatar
nitroman
Moderator
 
Posts: 3554
Joined: Fri 18.04.2003, 01:17
Location: Jacksonville, FL

Postby Fubar1764 » Thu 11.05.2006, 15:44

TommyK wrote: But as they say, "Beauty is in the eye of the beholder."

I always thought it was "Beauty is in the eye of the beer-holder". . . or was that just my college experience? :?
Nitro, are you sure that model in black is all OEM?
The most beautiful women per capita reside in Prague. Average women in Prague are smoking hot anywhere else (even by your tough standards, Nitro ;) )However, with a metric of sane/beautiful, Texas appears to have the most desireable women. . .probably because I don't speak Czech. :cry:
"Lawyer, gambler, bookie, loan-shark, light arson, sundry interests in areas of questionable legality"

-Your "Jack" of all trades
User avatar
Fubar1764
God
 
Posts: 1493
Joined: Fri 14.11.2003, 03:56

Postby Doug » Thu 11.05.2006, 19:04

nothing like a good Czech-mate :wink:
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA

Postby TommyK » Fri 12.05.2006, 01:14

Texas?!?! Prague I could buy into, but Texas? I could find more desirable women driving around the block once in San Fran than I could in a week in Dallas.
TommyK
Enthusiast
 
Posts: 167
Joined: Fri 01.10.2004, 22:38
Location: Benicia, CA

Postby Candles » Fri 12.05.2006, 07:14

TommyK wrote: I could find more desirable women driving around the block once in San Fran


And many more men.
User avatar
Candles
God
 
Posts: 1496
Joined: Tue 22.04.2003, 09:58
Location: Bristol, UK


Return to Hood/Top, Bodywork and Fittings

Who is online

Users browsing this forum: No registered users and 6 guests