Can anybody tell me where these wires should attach to ?! I thought it should be obvious but it's really not.
Think this is one of the original cables somebody made - if anybody has one can you please take a photo of it ?
| Home | WikiLEC | Repairs | Upgrades | Gallery | Buy & Sell | Mountain Chips | Meets & Events | Contact |
|
Broke My Elan Scan Cable !!
Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
4 posts
• Page 1 of 1
Broke My Elan Scan Cable !!
by simonbuk » Fri 08.11.2024, 18:20
You do not have the required permissions to view the files attached to this post.
Black S2 No.357
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
-
simonbuk - God
- Posts: 1600
- Joined: Sun 13.03.2016, 12:50
- Location: Mostly Worthing,West Sussex, sometimes the canals.......
Re: Broke My Elan Scan Cable !!
by RonR » Sat 09.11.2024, 18:45
Simon,
Unfortunately in your photo the wire attachment points are hidden behind the LED, but looking at the circuit board I'm pretty sure that the Red arrow points to 12 Volt connection and the Purple arrow points to the Data connection.
Plug the cable into the ALDL socket (making sure the loose wires don't touch) and turn the ignition on, then if you test the 2 broken wires with a voltmeter between each and the black wire (GND), the one which shows 12V should go to the RED arrow and the other to the Purple arrow.
Unfortunately in your photo the wire attachment points are hidden behind the LED, but looking at the circuit board I'm pretty sure that the Red arrow points to 12 Volt connection and the Purple arrow points to the Data connection.
Plug the cable into the ALDL socket (making sure the loose wires don't touch) and turn the ignition on, then if you test the 2 broken wires with a voltmeter between each and the black wire (GND), the one which shows 12V should go to the RED arrow and the other to the Purple arrow.
You do not have the required permissions to view the files attached to this post.
-
RonR - Fanatic
- Posts: 723
- Joined: Mon 22.08.2016, 20:25
- Location: Bromley
Re: Broke My Elan Scan Cable !!
by simonbuk » Sat 09.11.2024, 19:18
Ah yes - think you are right ! Moved the LED out of the way slightly -
Just need a small soldering iron now !
Just need a small soldering iron now !
You do not have the required permissions to view the files attached to this post.
Black S2 No.357
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
-
simonbuk - God
- Posts: 1600
- Joined: Sun 13.03.2016, 12:50
- Location: Mostly Worthing,West Sussex, sometimes the canals.......
Re: Broke My Elan Scan Cable !!
by simonbuk » Sun 17.11.2024, 17:02
Well the purple wire is showing 12V and the red wire 5V with the ignition on.
Better get my soldering iron out again...........
Better get my soldering iron out again...........
Black S2 No.357
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
Aqua Blue S2 No.385
Simonthesailor
"Twenty years from now you will be more disappointed by the things that you didn't do than by the ones you did. So buy an Elan" - Mark Twain.
-
simonbuk - God
- Posts: 1600
- Joined: Sun 13.03.2016, 12:50
- Location: Mostly Worthing,West Sussex, sometimes the canals.......
4 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 7 guests