Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
by mikecg » Fri 13.11.2026, 18:54
Hi, I have been viewing Tuga's video on how to fit the Mercedes Pump as a replacement for the original. I have not ordered one yet but they are now very reasonable.
Mine appears to have slightly differently wiring to Tuga's car.
Firstly my connection from the pump to the wiring loom is behind the nearside head lamp outer housing and it is also only one wire to each connection from the loom instead of two as Tuga shows us on his car. It also may just reach the pump with a bit of manoeuvering. As indicated the Mercedes pump has the same connector as the Elan pump
I have a Black and Black/slate from the loom which is correct. They inturn connect to the pump wiring a black and a brown. However in the process of removing the pump I split the loom conector (it comes apart) so I dont know which colour from the loom went to which colour on the pump? The wiring diagram does not provide the answer.. Some help here would be great?
-

mikecg
- Enthusiast
-
- Posts: 126
- Joined: Tue 29.12.2015, 15:11
- Location: Horley, Surrey
by KenS » Sat 14.11.2026, 13:00
A bit hesitant in putting this forward, I have checked my S2 and the pump Brown goes to loom Black and pump Black goes to loom Black/Grey. I was surprised, thinking that convention would be black to black (maintaining a black ground colour through the connector). Its probably worth checking pump flow direction before plumbing it in just to be sure, I assume the pump should suck on the center port and throw it out through the offset port. If you gain any knowledge on this it would be useful to post the outcome here. Good luck.
S2 M100 NMY #285
N/A 2010 Evora
-

KenS
- Fanatic
-
- Posts: 299
- Joined: Mon 27.10.2014, 21:04
- Location: North Kent Coast
by Fredjohn » Sat 14.11.2026, 13:39
Remember the recirculation pump pumps in the opposite direction to the normal direction.
La vie passe vite: vivez la avec élan.
Elan SE turbo 1992
Emira 2023
Mercedes Benz C200 estate
Lotus Evija Danish edition
-

Fredjohn
- God
-
- Posts: 2542
- Joined: Tue 21.08.2012, 00:30
- Location: Malvern, Worcs
by mikecg » Sat 14.11.2026, 18:49
Thanks guys, I will report back.
-

mikecg
- Enthusiast
-
- Posts: 126
- Joined: Tue 29.12.2015, 15:11
- Location: Horley, Surrey
by mikecg » Sat 21.11.2026, 19:19
Hi I have purchased a replacement Recirculating Pump from a web site called CarLightBulb which is a generic replacement Mercedes pump as fitted by Tuga in his Video. Mercedes part number 2038350064. It was £25.777 including postage. Extremely reasonable and appears to be very well made.
The end of the pump has the other half of the current connector built into the case so that the socket end of the connector on the wiring loom is a direct fit. The pump also has a useful "+" and "-" under the pins with the right pin as the positive pin which corresponds to the Black and Slate cable in the loom socket. My socket had come apart and the pins were loose so I was not sure which way roound they were supposed to be.
Also where the socket is in my car, behind the nearsside Headlamp, and because the pump body is a bit longer than the original I was able to just get the socket end of the wiring loom to reach the plug end of the pump without any modification.
All tested and the pump comes on fine and is pumping in the correct direction as per the arrow.
You do not have the required permissions to view the files attached to this post.
-

mikecg
- Enthusiast
-
- Posts: 126
- Joined: Tue 29.12.2015, 15:11
- Location: Horley, Surrey
Return to Heating and Cooling
Who is online
Users browsing this forum: No registered users and 6 guests