Lotus Elan Central

Everything M100

Skip to content

Removing old fuel filter

Alternator, waterpump, A/C, sensors, CAS, etc.

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Post a reply

Removing old fuel filter

Postby Galsia » Tue 15.01.2008, 21:12

.
Last edited by Galsia on Fri 07.05.2010, 09:09, edited 1 time in total.
User avatar
Galsia
Enthusiast
 
Posts: 213
Joined: Thu 08.11.2007, 08:06
Location: Derby
Top

Postby Specky » Wed 16.01.2008, 00:39

Yep..

Did you get a new seal...

They are not mentioned in the Elan manual but are in the espirt...

there's a thread on here some where..

when the union is undone support the pipe and turn the filter and pull equally.. It's quite stiff but it will pop out with a bump..
TTFN
If you have a problem, if no one else can help, and if you can find them, maybe you can hire... The N/A-Team.
User avatar
Specky
Moderator
 
Posts: 5982
Joined: Sun 07.09.2003, 23:19
Location: Swindon
Top

Postby DeeAitch » Wed 16.01.2008, 12:10

Be sure to get rid of any pressure in the line first or you will have fuel all over the place!
User avatar
DeeAitch
God
 
Posts: 1773
Joined: Fri 09.05.2003, 22:11
Location: North East
Top

Postby Galsia » Wed 16.01.2008, 14:22

.
Last edited by Galsia on Fri 07.05.2010, 09:09, edited 1 time in total.
User avatar
Galsia
Enthusiast
 
Posts: 213
Joined: Thu 08.11.2007, 08:06
Location: Derby
Top

Postby Specky » Wed 16.01.2008, 14:48

Don't worry to much about the pressure...

Leave it 5 mins.... as you've got a leak anyway..

And the fuel just goes over your hands and onto the tarmac/floor

So how many Scivets did you break getting in there.. :wink:

TTFN
If you have a problem, if no one else can help, and if you can find them, maybe you can hire... The N/A-Team.
User avatar
Specky
Moderator
 
Posts: 5982
Joined: Sun 07.09.2003, 23:19
Location: Swindon
Top

Postby M100 TWO » Wed 16.01.2008, 15:06

the O rings are a Rover part No it is O EDP9976 44pence each
john
Don't try to defie the law of physics! here endeth the first lesson
User avatar
M100 TWO
God
 
Posts: 926
Joined: Thu 02.10.2003, 14:49
Location: southampton
Top

Postby dapinky » Thu 17.01.2008, 01:50

Galsia wrote:and how do I do that? :)


I usually hit the inertia trip switch in the battery compartment (which kills the power to the pump) while the enine is running - as the pressure drops, the motor will stall leaving no pressure in the fuel lines.
Dave

Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it


...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
User avatar
dapinky
LEC Administrator
 
Posts: 10605
Joined: Sun 15.10.2006, 12:54
Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).
Top

Postby Galsia » Sun 20.01.2008, 19:54

.
Last edited by Galsia on Fri 07.05.2010, 09:08, edited 1 time in total.
User avatar
Galsia
Enthusiast
 
Posts: 213
Joined: Thu 08.11.2007, 08:06
Location: Derby
Top

Postby rip » Mon 28.01.2008, 00:59

I know where my filter should be, but have never managed to work out how to get to it. :shock:
1990 SE
User avatar
rip
God
 
Posts: 5904
Joined: Sun 08.04.2007, 07:48
Location: Milton Keynes, UK
Top

Postby Enright » Mon 28.01.2008, 01:42

Lift out the carpet inside your hood stowage cover.
Take the battery inspection cover and wedge it lengthways between the rear edge of the roof and the front edge of the stowage cover.
That will give you plenty of room to work (and is a really handy tip if you've ever got any other work to do in that area).
Undo all the screws and remove the plastic tray.

Then, from the driver's side, you'll be able to see the inspection hatch. It's an aluminium plate that's mounted vertically on the RHS of the fuel tank. Remove the 4 screws and voila, there's your fuel filter.
Striking fear into the hearts of duplicate posts everywhere...! :P

BCingU,
Neil ;-)
User avatar
Enright
Modificator
 
Posts: 4860
Joined: Sun 19.12.2004, 19:21
Location: Arnold, Nottingham, England
Top

Postby Specky » Mon 28.01.2008, 01:46

Enright wrote:Lift out the carpet inside your hood stowage cover.
Take the battery inspection cover and wedge it lengthways between the rear edge of the roof and the front edge of the stowage cover.
That will give you plenty of room to work (and is a really handy tip if you've ever got any other work to do in that area).
Undo all the screws and remove the plastic tray.

Then, from the driver's side, you'll be able to see the inspection hatch. It's an aluminium plate that's mounted vertically on the RHS of the fuel tank. Remove the 4 screws and voila, there's your fuel filter.


You forgot to break 1 in 3 scivets... :lol:

TTFN
If you have a problem, if no one else can help, and if you can find them, maybe you can hire... The N/A-Team.
User avatar
Specky
Moderator
 
Posts: 5982
Joined: Sun 07.09.2003, 23:19
Location: Swindon
Top

Postby rip » Tue 29.01.2008, 16:43

Hardly the most accessible then. :roll:
Nice tip about propping the stowage cover open.
1990 SE
User avatar
rip
God
 
Posts: 5904
Joined: Sun 08.04.2007, 07:48
Location: Milton Keynes, UK
Top
Post a reply

Return to Engine Ancillaries

Who is online

Users browsing this forum: No registered users and 5 guests

© 1998 – 2026 Lotus Elan Central. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group