Milky Milky! Not lovely...

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Milky Milky! Not lovely...

Postby Stef » Wed 29.06.2011, 16:28

As most of you will know, that despite a full respray a few years back, poor Blipi is pinking, and badly! :oops:

What are your top tips and top products to rectify this dull unpleasent milky formation?

I'd rather take the option of doing it well once and on occasion than frequent polishing. My arms aren't strong and I have little patience.

Cheers all!
Men are like a fine wine.
They begin as grapes, and it's up to women to stomp the sh * t out of them until they turn into something acceptable to have dinner with.
User avatar
Stef
TVR/PistonHeads Ambassador
 
Posts: 4016
Joined: Fri 01.08.2003, 14:23
Location: Northamptonshire

Re: Milky Milky! Not lovely...

Postby dapinky » Wed 29.06.2011, 17:41

If it was given a coat (or 2) of clearcoat laquer when it was resprayed, you may have a problem, as any milky appearance is usually to do with laquer coming away from the basecoat (caused by leaving the base coat too long before applying clearcoat).....

....however, if they just went for the good old-fashioned way of a solid colour and no clearcoat, then you wont beat an afternoon with the T-cut. (again, as it was only a couple of years ago, I'm making a basic assumption that they sprayed it with 2-pack paint, so it is 'hard' not 'soft' like cellulose.)

I have to do the red one once a year (as Angie doesn't polish it inbetween times!!!), it doesn't take that much effort, and the whole lot can be done in a couple of hours.

Wash it first, but don't use a shampoo with wax in it - i know the purists will scream in agony (due to the salt/chemicals in it) but a drop of washing-up liquid in warm water is good (a drop, mind - not a squirt or a splash - if you get it foaming, then it's too much - just something to break the surface tension of the droplets).

Dont need to leave it to dry/chamois it or anything posh - do the T-cut thing - one cloth to apply it, one to rub it off, and a soft one to polish it up.

Once done, apply a good quality (beeswax!) polish - paste/solid is usually better than liquid.

I know that there are lots of other opinions out there, some will no doubt tell you that you get a better shine with a different product etc etc etc, and i fully accept that this method will NOT give you a glass-like concouse finish, but it will do the job in half a day, not cost much, and is more than good enough for a car used regularly, not kept under cover in a garage.
Dave

Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it


...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
User avatar
dapinky
LEC Administrator
 
Posts: 10625
Joined: Sun 15.10.2006, 12:54
Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).

Re: Milky Milky! Not lovely...

Postby theelanman » Wed 29.06.2011, 21:15

Pay a detailer about £60 to mop n polish.......:-D
I’m normally not a praying man, but if you’re up there, please save me, Superman.
User avatar
theelanman
Moderator
 
Posts: 7296
Joined: Fri 30.04.2004, 15:52
Location: peak district

Re: Milky Milky! Not lovely...

Postby Stef » Thu 30.06.2011, 12:48

Great advice there. From both! :-D

Must admit, I have been lazy and been using the 'ol Fairy on her. Maybe a magic wand would have been better! Will note to use proper car poo in the future (slap wrist)

Don't think I had lacquer finish, will be really peeved if I have and this is the paing coming away then.

Who knows, for Donington she may shine! :lol:
Men are like a fine wine.
They begin as grapes, and it's up to women to stomp the sh * t out of them until they turn into something acceptable to have dinner with.
User avatar
Stef
TVR/PistonHeads Ambassador
 
Posts: 4016
Joined: Fri 01.08.2003, 14:23
Location: Northamptonshire

Re: Milky Milky! Not lovely...

Postby rip » Thu 30.06.2011, 19:22

You could try clay. Seems to take dirt away without being aggressive, leaving a smooth finish.

Why have you used washing-up liquid when car shampoo is easily available & inexpensive?
I noticed chunks out of the front & rear wing panels while we were at Snetterton. You won't polish those out. :cry:
1990 SE
User avatar
rip
God
 
Posts: 5905
Joined: Sun 08.04.2007, 07:48
Location: Milton Keynes, UK

Re: Milky Milky! Not lovely...

Postby Doug » Thu 30.06.2011, 20:20

Stef,
where have your priorities been? Surely you should have some boy toy you can make polish your car now and then!!
-D
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA

Re: Milky Milky! Not lovely...

Postby Stef » Fri 01.07.2011, 07:36

Hey Doug!

Chaps can be great, but sometimes restrictive, hence my lack of LEC involvement over the past few years :(

Hope to do better next time.

If you are offering a rub down, you're welcome to Sunny Northants anytime :wink:
Men are like a fine wine.
They begin as grapes, and it's up to women to stomp the sh * t out of them until they turn into something acceptable to have dinner with.
User avatar
Stef
TVR/PistonHeads Ambassador
 
Posts: 4016
Joined: Fri 01.08.2003, 14:23
Location: Northamptonshire

Re: Milky Milky! Not lovely...

Postby Doug » Tue 05.07.2011, 20:16

you know it, baby! :smt112
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA

Re: Milky Milky! Not lovely...

Postby Stef » Thu 07.07.2011, 16:15

If everyone believes in fairies enough, Blipi could be cured... :smt045
Men are like a fine wine.
They begin as grapes, and it's up to women to stomp the sh * t out of them until they turn into something acceptable to have dinner with.
User avatar
Stef
TVR/PistonHeads Ambassador
 
Posts: 4016
Joined: Fri 01.08.2003, 14:23
Location: Northamptonshire


Return to Hood/Top, Bodywork and Fittings

Who is online

Users browsing this forum: AhrefsBot and 3 guests