ElanScan Interface

[GeoffSmith]

Just come down from slaving over a hot soldering iron and I can confirm receipt of your e-mails Roger and Johan.

[Oscarthecat]

Feel free to add your name to the list and send me (Geof) an e-mail (elanscaninterfaces[ A T ]gmail[ D O T ]com)..

1. Roger D
2. Johanvanboven
3. Oscarthecat
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16

[lotusrepair]

What happened to the wireless version? Were they going to be produced?

[MarkP]

Feel free to add your name to the list and send me (Geof) an e-mail (elanscaninterfaces[ A T ]gmail[ D O T ]com)..

1. Roger D
2. Johanvanboven
3. Oscarthecat
4. MarkP
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16[/quote]

[Oscarthecat]

Thanks Geoff! Mine arrived safely today. Much appreciated.

[Roger D]

Geoff,

Got mine as well, thanks, now all I need to do is find out how to get it working on my Windows 10 laptop.

Any hints pease?

Cheers

Roger

[Aoki Magic Pants]

Feel free to add your name to the list and send me (Geoff) an e-mail (elanscaninterfaces[ A T ]gmail[ D O T ]com)..

1. Roger D
2. Johanvanboven
3. Oscarthecat
4. MarkP
5. Aoki Magic Pants
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16

[MarkP]

Thanks Geoff, my cable arrived today. Now for the software bit!
Regards
Mark

[Aoki Magic Pants]

Thanks Geoff. I received the cable today, I loved the appropriate regional colours used on the address

Cheers,

Phil.

[GeoffSmith]

And the size of the font.

[Aoki Magic Pants]

And the size of the font.

Definitely 3 tiers of football smaller

Thanks for the goodies too, if I can't figure out the Elan Scan Software, I can always use the extra paper clip and the pen to write down the codes!

[johanvanboven]

Ok, Elanscan cable works fine in device manager, but where to find software to make it running?

Could not find it in WikiLEC.

[GeoffSmith]

https://aldl-interfaces.smiths.im/

[Fredjohn]

You'll find the elanscan software here near top of page:
http://www.lotusm100.com/manuals

THIS LINK IS NO LONGER VALID.

SEE MANUALS TAB AT TOP OF THE FORUM PAGE, ONCE SIGNED IN

[johanvanboven]

Thx.

Installed and works.

[TorqueHorse]

Feel free to add your name to the list and send me (Geoff) an e-mail (elanscaninterfaces[ A T ]gmail[ D O T ]com)..

1. Roger D
2. Johanvanboven
3. Oscarthecat
4. MarkP
5. Aoki Magic Pants
6. TorqueHorse
7.
8.
9.
10.
11.
12.
13.
14.
15.
16

[Brit-Car-Nut]

Note: Just clearing the old list since they have all announced they received their interface.

Feel free to add your name to the list and send Geoff an e-mail (elanscaninterfaces[ A T ]gmail[ D O T ]com)...

1. TorqueHorse
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.

[Dave Thomas]

Hi all you elanscan experts. I finally made the OBD1 usb connector. (not as bad as I thought). First scan whilst the engine warming and here is the result which shows what happens when the engine cuts at 4000 revs with the injectors etc. What should be my next step? It doesn't look like overboost cut out.
BW, stay safe.
Dave Thomas
PS tried the upload and failed for Pages file, Word and PDF files- any suggestions
Could e-mail the graphs too

[Dave Thomas]

PS my e-mail address is thekipdr@aol.com

[dapinky]

PS tried the upload and failed for Pages file, Word and PDF files- any suggestions

If you save the .ecu file on your computer, then put it into a .zip file, you can upload that onto here......