Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
by rushing » Mon 17.03.2008, 15:56
Hi i need to replace my rear plastic window. A car uphostery place have quoted me £211.00. do you think this is cheap or is it a rip off. ?
thanks
-
rushing
- Enthusiast
-
- Posts: 233
- Joined: Thu 19.06.2003, 21:07
- Location: dunstable
by Sy V » Mon 17.03.2008, 16:00
Sounds dear. Why do you need to replace your window?
Talk and song from tongues of lilting grace, sounds caress my ears but not a word I heard could I relay, the story was quite clear - Robert PlantIn Respectful Memory - 21st March 1959 - 14th February 2016
-

Sy V
- LEC Godfather
-
- Posts: 5794
- Joined: Mon 21.04.2003, 07:06
- Location: Lydiate Ash, Bromsgrove, Worcestershire.
by rushing » Mon 17.03.2008, 16:17
misty and grey . i cant even see and reverse . too old now . plastic cracking .
-
rushing
- Enthusiast
-
- Posts: 233
- Joined: Thu 19.06.2003, 21:07
- Location: dunstable
by Sy V » Mon 17.03.2008, 16:19
If it's cracked then fair dos. But Renovo plastic window polish will clear the misting - I promise you.
Last edited by
Sy V on Mon 17.03.2008, 17:09, edited 1 time in total.
Talk and song from tongues of lilting grace, sounds caress my ears but not a word I heard could I relay, the story was quite clear - Robert PlantIn Respectful Memory - 21st March 1959 - 14th February 2016
-

Sy V
- LEC Godfather
-
- Posts: 5794
- Joined: Mon 21.04.2003, 07:06
- Location: Lydiate Ash, Bromsgrove, Worcestershire.
by rip » Mon 17.03.2008, 16:54
MER car polish does an ok job too. You are more likely to have some of that already.
1990 SE
-

rip
- God
-
- Posts: 5905
- Joined: Sun 08.04.2007, 07:48
- Location: Milton Keynes, UK
by clemo » Mon 17.03.2008, 18:50
save yourself time money( at that price) and future effort get a new hood or a new hood plus seals from trims..
if not shop around , thats very expensive,,,
Jim Clark S2 - 1/12. The one with the Yellow spoke wheels . No 613 on dash (pushed in to factory in wrong order 615 on tub)
-

clemo
- LEC Administrator
-
- Posts: 5069
- Joined: Mon 21.04.2003, 23:24
- Location: TORQUAY Devon. Cream first then Jam obviously.
by markv » Mon 17.03.2008, 22:25
Sy V wrote:If it's cracked then fair dos. But Renovo plastic window polish will clear the misting - I promise you.
Sorry, but it doesn't work for bad cases - I've tried. Yet to try the MER.
Regards
Mark/.
-

markv
- God
-
- Posts: 926
- Joined: Sun 28.05.2006, 15:57
- Location: Nottingham, UK
by Sy V » Tue 18.03.2008, 06:41
I find this hard to believe, Mark. Is there some other outside influence that has tarnished your window?
I agree that it takes time. But working in small circles, inside and outside surfaces, it should do the trick.
After all, it's only a plastic polish - mild abrasive.
Talk and song from tongues of lilting grace, sounds caress my ears but not a word I heard could I relay, the story was quite clear - Robert PlantIn Respectful Memory - 21st March 1959 - 14th February 2016
-

Sy V
- LEC Godfather
-
- Posts: 5794
- Joined: Mon 21.04.2003, 07:06
- Location: Lydiate Ash, Bromsgrove, Worcestershire.
by Galsia » Tue 18.03.2008, 08:30
Sy V wrote:I find this hard to believe, Mark. Is there some other outside influence that has tarnished your window?
I agree that it takes time. But working in small circles, inside and outside surfaces, it should do the trick.
After all, it's only a plastic polish - mild abrasive.
It didn't work on my rear window but mine is too far gone for cleaning I think..
Thread about it here.
-

Galsia
- Enthusiast
-
- Posts: 213
- Joined: Thu 08.11.2007, 08:06
- Location: Derby
by markv » Tue 18.03.2008, 12:22
Sy V wrote:I find this hard to believe, Mark. Is there some other outside influence that has tarnished your window?
I agree that it takes time. But working in small circles, inside and outside surfaces, it should do the trick.
After all, it's only a plastic polish - mild abrasive.
The rear window was in a bad state when I bought my elan - the previous owner said she'd tried all sorts of things but nothing worked. So far I've done two applications of Renovo (small circles, inside and out) and there was an improvement, but not enough to give me anything approaching good visibility - I can now see vague shapes rather than just a mist!
I think I took some before and after pictures, so if I can dig them out I'll post them.
Regards
Mark/.
-

markv
- God
-
- Posts: 926
- Joined: Sun 28.05.2006, 15:57
- Location: Nottingham, UK
by Sy V » Tue 18.03.2008, 13:04
Blimey!
I thought mine was bad - yours must have been like pea soup!
Talk and song from tongues of lilting grace, sounds caress my ears but not a word I heard could I relay, the story was quite clear - Robert PlantIn Respectful Memory - 21st March 1959 - 14th February 2016
-

Sy V
- LEC Godfather
-
- Posts: 5794
- Joined: Mon 21.04.2003, 07:06
- Location: Lydiate Ash, Bromsgrove, Worcestershire.
by Scott J » Mon 25.08.2008, 16:21
I use the Renova and stevo tried it to. If window is way past its best Renovo will not bring it back to new. it does improve visibility but I find myself polishing the window every 6 months. "running to stand still"
Some people beat Rambo from A to B.
-

Scott J
- The prodigal son
-
- Posts: 2277
- Joined: Mon 15.12.2003, 17:47
- Location: Westerton, Glasgow
by ektrolleyboy » Thu 04.09.2008, 11:09
Does anyone have any experience of Hindsight screen restorer? Is it really as good as it's made out to be? Before I go and blow 40 squid on a kit...
Pacific Blue-LOTUS ELAN S2 # 036 / Hot Orange-MINI COOPER S CABRIOLET
-
ektrolleyboy
- God
-
- Posts: 774
- Joined: Sat 11.11.2006, 11:35
- Location: Heaven And Hell!
by Jackonicko » Thu 04.09.2008, 15:15
It's got to be worth a try. The next step will cost you £200 minimum, or eight long and painful hours.
-
Jackonicko
-
by dermotbell » Thu 04.09.2008, 19:44
Tried it, not going to get rid of the dreaded misting, but it is better than renova.
Dermot Bell
-

dermotbell
- Fanatic
-
- Posts: 487
- Joined: Sun 11.06.2006, 21:04
- Location: Dubai
Return to Hood/Top, Bodywork and Fittings
Who is online
Users browsing this forum: No registered users and 1 guest