Post cries for help here if your topic fits no other thread in this category.
Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith
by paza1 » Tue 09.09.2008, 22:13
Neil,
Yea, I think you are correct. There is a return pipe to the filler neck but I can't see that it is enough for expansion.
Cheers
Mark
Silver 1992 SE Turbo.
-
paza1
- Fanatic
-
- Posts: 687
- Joined: Thu 09.06.2005, 22:46
- Location: Chester
by dapinky » Tue 09.09.2008, 22:42
Galsia wrote:Kinda related question here. What is the best way to unblock the drain pipe near the fuel filler cap? Mine is blocked and I keep finding water in there am worried about water getting into the fuel system. I've got a bit of sponge in at the moment.
Thanks.
I use a piece of 0.8mm MIG welding wire - it will push down the pipe and is rigid enough to go round the kink without causing any problems.
I got so fed up with the pipe clogging up that i keep a length of welding wire wrapped round the filler neck and feeding down the drain pipe.
There is enough clearance to allow water to drain away, but if it gets clogged with leaf debris (we live on a hill, opposite a park) a quick wiggle soon empties out the water.
Dave
Just the one now, but this one's mine! - and it will be finished eventually..... - but also temporary custodian of a project until it is finished enough for Angie to drive it
...oh, and a 2006 Freelander destined for the jungles of The Gambia - 4500 miles across roads, desert and tracks - what could possibly go wrong?
-

dapinky
- LEC Administrator
-
- Posts: 10605
- Joined: Sun 15.10.2006, 12:54
- Location: As far west as you can get in West Wales before you become Irish (Pembroke Dock).
by Galsia » Thu 11.09.2008, 13:53
.
Last edited by
Galsia on Thu 06.05.2010, 16:29, edited 1 time in total.
-

Galsia
- Enthusiast
-
- Posts: 213
- Joined: Thu 08.11.2007, 08:06
- Location: Derby
by Specky » Thu 11.09.2008, 19:41
Try pushing up if it won't go down...
TTFN
If you have a problem, if no one else can help, and if you can find them, maybe you can hire... The N/A-Team.
-

Specky
- Moderator
-
- Posts: 5982
- Joined: Sun 07.09.2003, 23:19
- Location: Swindon
by Ade » Thu 11.09.2008, 22:25
Hi all,
On clearing the pipe to drain away water. Mine as blocked a few times and an air hose as cleared it every time.
Ade
-
Ade
- Fanatic
-
- Posts: 311
- Joined: Tue 22.04.2003, 19:40
- Location: Broseley,Shropshire
by Jackonicko » Wed 28.01.2009, 18:37
Where do you push up FROM, exactly?
-
Jackonicko
-
by esprit888 » Wed 28.01.2009, 18:51
RayD wrote:Galsia,
I had trouble getting the wire round the bend, having said that mine wasn't blocked, but you can do it.
Test with water or WD40 to see if there’s a way through.
Try a small screwdriver in the hole without doing any damage, it should go down about 1½” to the bend. You may need to clean it out from the top.
Try pushing the wire up the pipe.
When it comes to getting the wire in from the top it needs to have a bend in it about a ¼” from the end and the bend needs to be pointing in the right direction...a bit of trial and error but generally away from you and to the left as you are stand at the side of the car...have another go.
Ray
Mine was plugged solid, i simply connected an air nozzle to the local garages air line (when they were not looking

) and blew it out. It went with a 'POP' and a plug of crap splattered on the floor just in front of the rear wheel. Flushed it with soapy water and no problems since

-

esprit888
- God
-
- Posts: 957
- Joined: Fri 31.10.2008, 18:56
- Location: Lotus Land-Canada
by Paul.P » Wed 28.01.2009, 19:11
Galsia wrote:Kinda related question here. What is the best way to unblock the drain pipe near the fuel filler cap? Mine is blocked and I keep finding water in there am worried about water getting into the fuel system. I've got a bit of sponge in at the moment.
Galsia, try getting one of them plastic straws, it should fit the hole pretty tight, then blow down the straw, it cleared mine straight away, then you can just keep a spare straw in the glove compartment. Try McDonalds, they have loads !
JPS M100 was built from bare chassis up to create one off M100 in the mould of JPS Team Lotus
-
Paul.P
- God
-
- Posts: 4970
- Joined: Sun 14.12.2003, 18:18
- Location: Oakham, Rutland
-
by dedmans » Wed 28.01.2009, 19:33
as posted once before use water absorbant in the tank. Overnight it will all go.
I could only clear my drain pipe with a length of 5mm electric wire, stuck it in and gave it a hard up and down plunge. other methods did not work for me.
All black S2
-
dedmans
- Tinkerer
-
- Posts: 68
- Joined: Mon 18.06.2007, 21:34
- Location: hampshire england
by RayD » Sat 13.10.2012, 21:53
-

RayD
- Forum Member
-
- Posts: 2142
- Joined: Mon 20.03.2006, 19:45
- Location: South Yorkshire
by dedmans » Sat 13.10.2012, 22:45
Air compressor with the right adapter was the final method that I used. Had to do it regularly. No longer a problem to me as sadly the car has gone. Miss it but really like like the Z3 that we have now.
All black S2
-
dedmans
- Tinkerer
-
- Posts: 68
- Joined: Mon 18.06.2007, 21:34
- Location: hampshire england
Return to Miscellaneous Problems - Need Help!
Who is online
Users browsing this forum: No registered users and 3 guests