Lotus Elan Central

Everything M100

Skip to content

Cracked exhaust

Moderators: theelanman, dapinky, Specky, clemo, Nige, Sy V, Dave Eds, DaveT, Elanlover, muley, Enright, algirdas, nitroman, GeoffSmith

Post a reply

Cracked exhaust

Postby dans » Tue 27.09.2005, 18:59

Hi,

I seem to have a crack around where the very front of the exhaust goes into the pre cat <correction>.

Is it likely to be possible to get this welded up? Just as a short term measure to keep the car going until I can arrange a replacement exhaust?

Image

Cheers,
DAN
Last edited by dans on Tue 27.09.2005, 20:26, edited 1 time in total.
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby stevo » Tue 27.09.2005, 20:16

you could indeed weld it up but it would be a short term bodge. BTW the bit its bolted on to is the pre-cat not the manifold. :)
arancio baby! thats italian for orange! i think?
User avatar
stevo
God
 
Posts: 1897
Joined: Mon 21.04.2003, 17:16
Location: Aboyne, royal deeside, scotland
Top

Postby dans » Tue 27.09.2005, 20:24

BTW the bit its bolted on to is the pre-cat not the manifold

Thanks for the tip. :roll:

I could really do with a car this weekend and, of course, I just sold my other car last weekend!!!! :x So if can get away with a short term bodge.....
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby stevo » Tue 27.09.2005, 20:28

this is a weak point in the exhaust system as the engine vibrates on its mounts the joint takes the punishment. most people with aftermarket systems have a flexy coupling fitted just behind this joint to eliminate the problem.
arancio baby! thats italian for orange! i think?
User avatar
stevo
God
 
Posts: 1897
Joined: Mon 21.04.2003, 17:16
Location: Aboyne, royal deeside, scotland
Top

Postby dans » Tue 27.09.2005, 20:38

any special hints on getting it welded?
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby Monty » Tue 27.09.2005, 20:49

dans wrote:any special hints on getting it welded?


Someone with a welder :idea: LMAO.

Just go to an Exhaust place or even a garage
Image
User avatar
Monty
Chunder King!
 
Posts: 7977
Joined: Sun 11.01.2004, 22:32
Location: Leeds
Top

Postby Doug » Tue 27.09.2005, 21:02

yes, just tell them to be careful so they don't weld the PAS lines, etc.

this is a common fault as Stevo pointed out. Mine sure sounded race-worthy when cracked like this! :D

You can drive it like that if you want though, but yes replacement exhaust is the better way to go than pay for Lotus replacement parts -- there's loads of info on everyone's exhaust adventures within the Forum . . .
Image
User avatar
Doug
LEC Founder
 
Posts: 7468
Joined: Thu 17.04.2003, 06:43
Location: Oregon Coast, USA
Top

Postby stevo » Tue 27.09.2005, 21:14

do you want a stiffy :wink:
arancio baby! thats italian for orange! i think?
User avatar
stevo
God
 
Posts: 1897
Joined: Mon 21.04.2003, 17:16
Location: Aboyne, royal deeside, scotland
Top

Postby dans » Tue 27.09.2005, 21:59

Hadn't read the 'Stiffy' project before.
Sounds like I probably do so i'll have to have a think about that!!

Have been keeping an eye on the Bargain Exhaust post for a while :wink:
Sounds like a good time for an upgrade to me!

Thanks for the tips, off to find myself one of those welder thingys now :roll: :roll:
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby Dico » Wed 28.09.2005, 19:02

Bang some Gum Gum paste on it as a temporary fix. Its not flexible i dont think but should keep you going for a while.
available from halfords £2.99 iirc.

Using it on mine at the mo whilst awaiting for Stevo to get a hard on.
4+ hours stuck in a damp bucket seat with a mad Irishman at the wheel - Deep joy!!!!
User avatar
Dico
Fool Boy Four - Founder
 
Posts: 3569
Joined: Mon 01.12.2003, 09:45
Location: Moderator Manchester
Top

Postby dans » Wed 28.09.2005, 19:14

Thanks Dico, had occurred to me that might be the easiest way to go but wasn't sure how long it will hold. May give it ago then!!

Cheers,
DAN
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby John_W » Wed 28.09.2005, 19:38

Dico wrote:Bang some Gum Gum paste on it as a temporary fix. Its not flexible i dont think but should keep you going for a while.
available from halfords £2.99 iirc.

Ah, Gun Gum...
A real blast from the past. Memories of old minis and impecunious student days.
Dico wrote:Using it on mine at the mo ...

Good to see craftmanship isn't dead. Good on yer, Dico.

John :wink:
User avatar
John_W
Heid-bummer
 
Posts: 3780
Joined: Mon 21.04.2003, 12:31
Location: Aberdeen
Top

Postby Dico » Wed 28.09.2005, 20:56

Did mine the day before its MOT and it passed with flying colours.
once you've applied it moisten it with a damp cloth/finger, turns out really neat.
Apply whilst the exhaust is hot and let harden at least partialy before use or it'll just blast away.

You cant beat a good bodge!
4+ hours stuck in a damp bucket seat with a mad Irishman at the wheel - Deep joy!!!!
User avatar
Dico
Fool Boy Four - Founder
 
Posts: 3569
Joined: Mon 01.12.2003, 09:45
Location: Moderator Manchester
Top

Postby dans » Wed 28.09.2005, 21:11

better go and dig out the latex gloves then......... :shock: :roll:
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby Sy V » Thu 29.09.2005, 08:24

Moistening, latex gloves and stiffies all on one page...surprised Stef hasn't offered any input yet!

:wink:
Image

Talk and song from tongues of lilting grace, sounds caress my ears but not a word I heard could I relay, the story was quite clear - Robert Plant

In Respectful Memory - 21st March 1959 - 14th February 2016
User avatar
Sy V
LEC Godfather
 
Posts: 5794
Joined: Mon 21.04.2003, 07:06
Location: Lydiate Ash, Bromsgrove, Worcestershire.
Top

Postby stevo » Thu 29.09.2005, 10:35

give her time. :D
arancio baby! thats italian for orange! i think?
User avatar
stevo
God
 
Posts: 1897
Joined: Mon 21.04.2003, 17:16
Location: Aboyne, royal deeside, scotland
Top

Postby Stef » Thu 29.09.2005, 12:59

Sorry I was in a noisy zaust topless mode exposing myself to the local masses for admiration. :P

So, latex gloves on to release gun gum on the underside of a hot body... interesting. Yep. A stiffy is required! :D
Men are like a fine wine.
They begin as grapes, and it's up to women to stomp the sh * t out of them until they turn into something acceptable to have dinner with.
User avatar
Stef
TVR/PistonHeads Ambassador
 
Posts: 4016
Joined: Fri 01.08.2003, 14:23
Location: Northamptonshire
Top

Postby dans » Thu 29.09.2005, 14:51

What sort of flexible section to be people put in to prevent this from happening again?

Cheers
User avatar
dans
Fanatic
 
Posts: 472
Joined: Tue 26.04.2005, 19:14
Location: Cotswolds
Top

Postby F1 LOTUS » Thu 29.09.2005, 20:43

Braided stainless like the one in the picture: -
http://www.lotuselancentral.com/forum/v ... t=downpipe
User avatar
F1 LOTUS
God
 
Posts: 2199
Joined: Thu 17.04.2003, 18:17
Location: SoCal, USA
Top

Postby Matt RI » Sat 01.10.2005, 14:42

Good up close to show the location, Brian. It does not need to be a long piece- here is a shot of mine peeking out:
You do not have the required permissions to view the files attached to this post.
User avatar
Matt RI
Fanatic
 
Posts: 365
Joined: Fri 10.12.2004, 04:42
Location: Rhode Island
Top
Next
Post a reply

Return to Exhaust

Who is online

Users browsing this forum: No registered users and 1 guest

© 1998 – 2026 Lotus Elan Central. All rights reserved.
Powered by phpBB® Forum Software © phpBB Group